Genuine HOMAN 3501B-051 H3 10-tooth brake slack adjuster compatible with Sinotruk HOWO, Sitrak NG, and A7 models.
When it comes to heavy-duty truck safety, few components matter more than your braking system — and the HOMAN 3501B-051 H3 brake slack adjuster plays a critical role in keeping your Sinotruk running safely mile after mile.
Designed as a direct-fit replacement for Sinotruk HOWO, A7, and Sitrak NG series Xe tải, this 10-tooth slack adjuster ensures consistent brake response by maintaining proper pushrod travel and automatically compensating for lining wear. Without a properly functioning slack adjuster, your brakes can become delayed, uneven, or even fail under load — putting drivers and cargo at risk.
Manufactured to match original HOMAN engineering standards, the 3501B-051 features a forged steel body for high impact resistance and long-term durability under extreme conditions. The precision-cut 10-spline input hub provides secure engagement with the S-cam, reducing play and minimizing noise during operation. Zinc-plated finish resists corrosion, making it ideal for use in humid ports, dusty mines, or rainy climates across Africa, Latin America, and Southeast Asia.
Whether you’re servicing a fleet of logging haulers in Colombia, long-haul freighters in Kenya, or construction rigs in Indonesia, using genuine-spec parts like the HOMAN 3501B-051 means fewer roadside breakdowns and better compliance with local transport regulations.
| Feature |
Specification |
| Số phần |
3501B-051 |
| Brand |
HOMAN H3 Series |
| Kiểu |
Automatic Brake Slack Adjuster |
| Tooth Count |
10 Răng (Spline Input) |
| Khả năng tương thích |
Sinotruk HOWO T5G, T7h, A7, Sitrak NG |
| Mounting Position |
Đằng trước & Rear Axles (Left/Right) |
| Shaft Diameter |
32 mm |
| Adjustment Range |
±4.5° automatic compensation |
| Torque Spec |
180–220 Nm |
| Vật liệu |
Forged Carbon Steel |
| Surface Treatment |
Zinc Plating with Passivation |
| Operating Temperature |
-40°C to +120°C |
| Safety Standard |
Meets GB/T 564–2019 & ECE R27 |
1. CHÚNG TÔI ĐỐI XỬ VỚI MỌI KHÁCH HÀNG LÀ BẠN CỦA CHÚNG TÔI, BẤM VÀO NGUYÊN TẮC: CHIẾN THẮNG VÀ LỢI ÍCH THƯƠNG MẠI ;
2. NHIỀU SỰ LỰA CHỌN CHO SẢN PHẨM: CHẤT LƯỢNG, NHÃN HIỆU, BAO BÌ;
3. CHÚNG TÔI SẼ TRẢ LỜI BẠN CHO YÊU CẦU CỦA BẠN 24 GIỜ.
4.Nhà cung cấp phụ tùng Perfomance SINOTRUCK chuyên nghiệp
5. CHÚNG TÔI SẼ PHỤC VỤ 24/24 GIỜ TRONG NGÀY LÀM VIỆC.
6. ASS: CHÚNG TÔI SẼ CUNG CẤP CHO BẠN DỊCH VỤ SAU BÁN HÀNG TỐT NHẤT.
Always inspect both left and right-side slack adjusters during brake maintenance. Before installing the 3501B-051 H3 unit, clean the S-cam shaft thoroughly and check for wear or pitting. Slide the adjuster onto the camshaft smoothly—do not hammer. Ensure the splines engage fully (10 teeth design). Tighten the nut to 180–220 Nm using a torque wrench, then back off slightly to align the cotter pin hole. Recheck brake stroke after installation; it should be within 25–30 mm. Test brakes at low speed before full operation. Replace in pairs if excessive wear is found on either side.
