Genuine SINOTRUK WG9925530058 intercooler hose for HOWO T7H, C7H & A7 trucks. OEM replacement for turbo-to-intercooler airflow
If your SINOTRUK HOWO is losing power, running hotter than usual, or triggering a “reduced engine performance” warning, don’t jump straight to the turbocharger — the issue might be simpler: a cracked or swollen intercooler hose, like the original WG9925530058 used across T7H, C7H, and A7 models.
This genuine SINOTRUK intercooler hose connects the turbocharger outlet to the intercooler inlet, carrying pressurized, hot air before it’s cooled and sent into the engine. It’s built to handle extreme conditions: temperatures up to 180درجة مئوية, boost pressures over 2.5 حاجِز, and constant vibration from heavy-duty hauling. Unlike generic rubber hoses that degrade quickly, this OEM unit features a triple-layer construction — inner EPDM liner for heat resistance, embedded polyester fabric for strength, and outer UV-stable silicone coating to prevent cracking.
| Feature |
Specification |
| رقم القطعة |
WG9925530058 |
| Product Type |
Intercooler Hose (Charge Air Pipe) |
| Position |
Turbo Outlet to Intercooler Inlet |
| Inner Material |
Heat-Resistant EPDM Rubber |
| Reinforcement Layer |
Woven Polyester Fabric (x2) |
| Outer Coating |
Silicone with Anti-Static Wire |
| نطاق درجة الحرارة |
-40° C إلى +180 درجة مئوية (Peak) |
| Max Boost Pressure |
2.8 حاجِز |
| Hose Diameter |
Ø63 mm (2.5″) |
| Length (Center-to-Center) |
Approx. 420 مم |
| Clamp Type |
OEM-Style Worm Drive (M16–M70) |
| التوافق |
SINOTRUK HOWO T7H, C7H, A7, ZZ1257 Series |
| Engine Models |
MC11, MC13, د10, WD615 |
| OEM Standard |
Meets Q/01JZ007 & GB/T 7528-2020 |
| Packaging |
Shrink-Wrapped + Rigid Carton |
1. نتعامل مع كل عميل كصديق لنا, التمسك بالمبدأ: مربح للجانبين ومزايا متبادلة ;
2. مجموعة متنوعة من الخيارات للمنتجات: جودة, الماركة, التعبئة والتغليف;
3. سنقوم بالرد عليك لاستفسارك في 24 ساعات.
4.المورد المهنية أجزاء ساينو تراك برفومانس
5. سنكون في الخدمة 24/24 ساعات في يوم العمل.
6. الحمار: سوف نقدم لك أفضل خدمة بعد البيع.
Always relieve boost pressure before working on the intake system. Disconnect the battery ground to prevent accidental ECU errors. Loosen the two hose clamps at each end of the old WG9925530058 hose using a 7mm socket or screwdriver. Carefully pull the hose off the turbo outlet and intercooler inlet — don’t pry with metal tools, which can damage soft couplings. Clean any oil residue or carbon buildup from the mating flanges. Install the new OEM hose by hand, ensuring it seats fully on both ends. Reuse only if clamps are in perfect condition; otherwise, replace with new OEM-style worm-drive clamps. Tighten to 2.5–3.0 Nm — over-tightening can crush the silicone-reinforced walls. After installation, inspect for kinks or twists. Start the engine and check for whistling noises under load — a sign of air leaks. Use soapy water on joints to detect small leaks.
