Genuine SINOTRUK WG9925530058 intercooler hose for HOWO T7H, C7H & A7 trucks. OEM replacement for turbo-to-intercooler airflow
If your SINOTRUK HOWO is losing power, running hotter than usual, or triggering a “reduced engine performance” warning, don’t jump straight to the turbocharger — the issue might be simpler: a cracked or swollen intercooler hose, like the original WG9925530058 used across T7h, C7H, and A7 models.
This genuine SINOTRUK intercooler hose connects the turbocharger outlet to the intercooler inlet, carrying pressurized, hot air before it’s cooled and sent into the engine. It’s built to handle extreme conditions: temperatures up to 180°C, boost pressures over 2.5 thanh, and constant vibration from heavy-duty hauling. Unlike generic rubber hoses that degrade quickly, this OEM unit features a triple-layer construction — inner EPDM liner for heat resistance, embedded polyester fabric for strength, and outer UV-stable silicone coating to prevent cracking.
| Feature |
Specification |
| Số phần |
WG9925530058 |
| Product Type |
Intercooler Hose (Charge Air Pipe) |
| Position |
Turbo Outlet to Intercooler Inlet |
| Inner Material |
Heat-Resistant EPDM Rubber |
| Reinforcement Layer |
Woven Polyester Fabric (x2) |
| Outer Coating |
Silicone with Anti-Static Wire |
| Phạm vi nhiệt độ |
-40°C to +180°C (Peak) |
| Max Boost Pressure |
2.8 thanh |
| Hose Diameter |
Ø63 mm (2.5″) |
| Length (Center-to-Center) |
Approx. 420 mm |
| Clamp Type |
OEM-Style Worm Drive (M16–M70) |
| Khả năng tương thích |
SINOTRUK HOWO T7H, C7H, A7, ZZ1257 Series |
| Engine Models |
MC11, MC13, D10, WD615 |
| OEM Standard |
Meets Q/01JZ007 & GB/T 7528-2020 |
| Packaging |
Shrink-Wrapped + Rigid Carton |
1. CHÚNG TÔI ĐỐI XỬ VỚI MỌI KHÁCH HÀNG LÀ BẠN CỦA CHÚNG TÔI, BẤM VÀO NGUYÊN TẮC: CHIẾN THẮNG VÀ LỢI ÍCH THƯƠNG MẠI ;
2. NHIỀU SỰ LỰA CHỌN CHO SẢN PHẨM: CHẤT LƯỢNG, NHÃN HIỆU, BAO BÌ;
3. CHÚNG TÔI SẼ TRẢ LỜI BẠN CHO YÊU CẦU CỦA BẠN 24 GIỜ.
4.Nhà cung cấp phụ tùng Perfomance SINOTRUCK chuyên nghiệp
5. CHÚNG TÔI SẼ PHỤC VỤ 24/24 GIỜ TRONG NGÀY LÀM VIỆC.
6. ASS: CHÚNG TÔI SẼ CUNG CẤP CHO BẠN DỊCH VỤ SAU BÁN HÀNG TỐT NHẤT.
Always relieve boost pressure before working on the intake system. Disconnect the battery ground to prevent accidental ECU errors. Loosen the two hose clamps at each end of the old WG9925530058 hose using a 7mm socket or screwdriver. Carefully pull the hose off the turbo outlet and intercooler inlet — don’t pry with metal tools, which can damage soft couplings. Clean any oil residue or carbon buildup from the mating flanges. Install the new OEM hose by hand, ensuring it seats fully on both ends. Reuse only if clamps are in perfect condition; otherwise, replace with new OEM-style worm-drive clamps. Tighten to 2.5–3.0 Nm — over-tightening can crush the silicone-reinforced walls. After installation, inspect for kinks or twists. Start the engine and check for whistling noises under load — a sign of air leaks. Use soapy water on joints to detect small leaks.
