Genuine Sinotruk HOWO 081V04302-0062 Valve Push Rod
This authentic Sinotruk HOWO valve push rod (ສ່ວນທີບໍ່: 081V04302-0062) is engineered to exact OEM specifications, ensuring optimal valve timing and engine performance in HOWO trucks. Designed for heavy-duty applications, it transmits motion from the camshaft to the rocker arms with precision, reducing wear and maintaining engine efficiency under extreme conditions. The hardened steel construction and heat-treated ends ensure longevity and reliability, making it a critical replacement for engine maintenance and rebuilds.
Technical Specifications:
Material: Heat-treated alloy steel (ຊັ້ນ: 10.9 tensile strength)
Diameter: 10.0 ± 0.05 ມມ
Length: 245.0 ± 0.1 ມມ
Surface Finish: Precision ground (Ra ≤ 0.4 μm)
Compatibility: HOWO A7, T7H series with WEICHAI WP10/WP12 engines
Temperature Resistance: -40°C to +250°C
Load Capacity: Supports compressive loads up to 1500 N
Manufacturing Standard: ISO 9001 ຢັ້ງຢືນ, OEM tolerances
1. ພວກເຮົາຮັກສາລູກຄ້າທຸກຄົນທີ່ເປັນເພື່ອນຂອງພວກເຮົາ, ຮີບຮ້ອນຕໍ່ຫຼັກການພື້ນຖານ: ເງິນຊ່ວຍເຫຼືອ WIN-WIN ແລະ MUTUAL ;
2. ລາຍລະອຽດຂອງທາງເລືອກ ສຳ ລັບຜະລິດຕະພັນ: ຄຸນນະພາບ, ຍີ່ຫໍ້, ກະເປົ.າ;
3. ພວກເຮົາຈະຕອບແທນທ່ານ ສຳ ລັບຄວາມຕ້ອງການຂອງທ່ານພາຍໃນ 24 ຊົ່ວໂມງ.
4.ຜູ້ສະ ໜອງ ຊິ້ນສ່ວນ SINOTRUCK ທີ່ເປັນມືອາຊີບ
5. ພວກເຮົາຈະຢູ່ໃນການບໍລິການ 24/24 ຊົ່ວໂມງໃນວັນເຮັດວຽກ.
6. ເອສ: ພວກເຮົາຈະສະ ເໜີ ໃຫ້ທ່ານບໍລິການຫລັງການຂາຍທີ່ດີທີ່ສຸດ.
Installation Notes
Pre-Installation Checklist:
1.Inspect Components: Verify part number (081V04302-0062) and check for straightness or damage (roll on flat surface to detect bends).
2.Clean Surfaces: Ensure lifter bores and rocker arm contacts are free of debris and oil residue.
3.Lubrication: Apply clean engine oil to both ends of the push rod before installation.
Installation Steps:
1.Position Push Rod: Insert the push rod into the lifter bore, ensuring it sits squarely on the lifter cup.
2.Align with Rocker Arm: Gently guide the upper end into the rocker arm socket.
3.Valve Lash Adjustment: Set valve clearance to 0.25–0.30 mm (cold engine) using a feeler gauge.
4.Torque Specifications: Tighten rocker arm shaft bolts to 85 ± 5 Nm in the manufacturer’s specified sequence.
Critical Warnings:
Never reuse old push rods; replace in sets per cylinder to ensure uniform performance.
Check lifter and rocker arm wear before installation to prevent premature failure.
Avoid over-tightening; use a calibrated torque wrench for accuracy.
Post-Installation:
Prime the oil system before startup to ensure proper lubrication.
Run the engine at idle and monitor for unusual valve train noises.
Re-check valve clearance after the first 500 km of operation
